硼的添加对Ti0.26Zr0.07V0.24Mn0.1Ni0.33贮氢合金结构和电化学性能的影响

Ti_0.26Zr_0.07V_0.24Mn_0.1Ni_0.33Bx(x=0~0.10)系列合金均有V基固溶体相和C14型Laves相两相组成。添加B可提高Ti_0.26Zr_0.07V_0.24 Mn_0.1Ni_0.33合金的放电容量, Ti_0.26Zr_0.07V_0.24Mn_0.1Ni_0.33B0.1合金电极在60 mA·g^-1电流放电时的放电容量达到476.7 mAh·g^-1.B的添加不同程度地降低了合金的高倍率放电性能, 使合金电极表面上电化学反应的电荷转移电阻(R_ct)显着增加, 交换电流密度(I₀)显着降低。添加B可显着改善Ti_0.26Zr_0.07V_0.24Mn_0.1Ni_0.33合金电极的高温放电性能, Ti_0.26Zr_0.07V_0.24Mn_0.1Ni_0.33B_0.025合金电极在343 K高温下其放电容量达到525.6 mAh·g^-1.     

随机参数智能桁架结构动力特性分析

文中针对随机参数压电智能桁架结构研究了基于概率的结构动力特性分析方法。建立了压电主动檑和被动杆结构材料的质量密度、弹性模量同时具有随机性时结构的刚度矩阵和质量矩阵；从结构振动的瑞利商表达式出发，利用代数综合法推导出结构特征值随机变量数字特征的计算表达式。最后通过两个算例考察了智能桁架结构物理参数的随机性对其动力特性的影响，并获得了一些有意义的结论。     

建筑结构动力特性动点脉动测试

介绍用无人工激励动点测试（动点脉动测试）方法确定建筑物的自振频率，振型和阻尼。使用这一方法对南京电视塔、多层基础隔振房屋及水塔等进行了动力性能测试，获得了满意的结果。     

横观各向同性体应力波传播问题的特征分析

本文根据广义特征理论,对横观各向同性体轴对称弹性波传播问题进行了理论分析。提出了一个简化特征分析的方法,这种方法将成为应用特征线法求解各类各向异性应力波问题的一个突破口。     

Existence and uniqueness of optimal solutions for multirate partial differential algebraic equations

The numerical simulation of electric circuits including multirate signals can be done by a model based on partial differential algebraic equations. In the case of frequency modulated signals, a local frequency function appears as a degree of freedom in the model. Thus the determination of a solution with a minimum amount of variation is feasible, which allows for resolving on relatively coarse grids. We prove the existence and uniqueness of the optimal solutions in the case of initial-boundary value problems as well as biperiodic boundary value problems. The minimisation problems are also investigated and interpreted in the context of optimal control. Furthermore, we construct a method of characteristics for the computation of optimal solutions in biperiodic problems. Numerical simulations of test examples are presented.     

Glow Discharge Characteristics of Hollow Needle-Plate Electrode in Atmospheric Pressure ArgonSCIEI北大核心CSCD

Atmosphere pressure uniform plasma has the broad application prospect in the industrial field. Using hollow needle cathode - plate anode device excited by direct-current voltage, a uniform and stable glow discharge is generated at atmospheric pressure in ambient air with argon used as working gas. The influence of the experimental parameters (including gas flow rate and the gas gap width) on discharge has been investigated by optical method. It can be found that a glow-discharge plasma column can bridge the two electrodes. The plasma column is uniform, and no filaments can be discerned. Near the plate electrode, the diameter of the plasma column is largest of all positions. The maximal diameter of the plasma column increases with increasing the discharge current or the gas flow rate. Through electrical method, the voltage-current characteristic has been investigated. It has been found that the discharge voltage decreases with increasing the current which is similar with the characteristic of glow discharge in low pressure. It increases with increasing the gas gap width or the gas flow rate. By analyzing the optical emission spectrum scanning from 330 to 450 nm emitted from the direct-current glow discharge, the molecular vibrational temperature and the intensity ratio of spectral lines I-391.4/I-337.1 have been investigated as functions of the gas flow rate and gas gap width. Results indicate that both the vibrational temperature and the intensity ratio of spectral lines I-391.4/I-337.1 decrease with increasing the gas flow rate or the gas gap width. In addition, the molecular vibrational temperature and the intensity ratio of spectral lines I-391.4/I-337.1 have been investigated in spatial resolution along the direction of gas flow(plasma column axial), and give a qualitative analysis as well. It is found that the vibrational temperature and the average electron energy increase with increasing the distance from the hollow needle cathode. These results are important to the industrial applications of glow discharge.     

基于ZigBee网络和超声定位的智能跟随小车

基于成熟的IEEE802.15.4协议和ZigBee无线模块,结合超声定位,设计了一种新颖的智能跟随系统。设计的核心为PIC18F4620单片机和MRF24J40MA无线收发模块,通过无线收发来完成节点间的识别与同步,同时以超声测距系统完成对被跟踪目标的定位,通过控制驱动电机动作实现对指定目标的定距离跟随。控制网络以子网的形式控制不同系统的分时定位跟随,同时管理各移动定位系统的入网和切换。样机测试结果表明系统达到了预期的跟随设计要求,具有一定的工程使用价值。     

Investigation of the performance of bipolar transverse plate ESP in the sintering flue control

In order to improve the particle collection efficiency of the electrostatic precipitator (ESP), a transverse plate ESP with bipolar discharge electrodes is proposed. The simulations of the velocity distribution have shown that when the inlet velocity is 1 m/s, within the range of 40 mm from electrode plate, the average velocities of windward side and leeward side are less than 0.7 m/s and 0.3 m/s respectively. It is clear that the velocity near the collection electrode plate of this bipolar ESP is much lower than that of the ordinary ESP at the same inlet velocity. This low velocity can lead to higher efficiency for fine dust collection due to the less dust re-entrainment in ESP. It is also found that the average velocities are getting lower when the distance between plates electrodes are greater than 150 mm in accordance with the simulations. The voltage current characteristics of the bipolar ESP are superior to the ordinary ESP. The pressure drop of the bipolar ESP is about 30% higher than that of the ordinary one. The dust penetration of the bipolar ESP is about 54% less than that of the ordinary ESP when the sintering dust with 25.405 μm mass median diameter is used as the test particulate under the condition of the electric field from 2.1 kV/cm to 3.2 kV/cm and the velocity from 1.0 m/s to 1.5 m/s.     

铷蒸气激光器3D理论模型的建立及阈值特性模拟

基于三能级速率方程理论,结合惠更斯-菲涅尔衍射积分公式,利用分步光束传播方法建立了半导体泵浦碱金属蒸气激光器(DPAL)端面泵浦3D理论计算模型,用于模拟研究铷蒸气激光器的泵浦阈值特性。该模型将光束传播、光与物质相互作用独立考虑,利用迭代算法求解。考虑激光器腔内模式与泵浦光模式匹配对阈值特性的影响,模拟了单端泵浦铷蒸气激光器内部的三维动力学过程。在具体算例中研究了模式匹配最佳时,在阈值工作状态下铷蒸气室中的三维粒子数分布,以及沿不同轴线的增益分布。仿真了在最佳模式匹配位置附近,泵浦光模式变化对阈值特性的影响。根据蒸气池中粒子数分布和光场分布具体分析了模式匹配影响阈值特性的机理。同时还模拟了不同长度蒸气池对阈值特性的影响。结果表明,腔参数与泵浦光模式之间存在一定的关系,对于特定的泵浦光模式,存在恰当的腔参数,使得阈值达到最小。     

Evaluation of the dosimetric characteristics of a radiophotoluminescent glass dosimeter for high-energy photon and electron beams in the field of radiotherapy

We aimed to evaluate the suitability of a glass dosimeter (GD) for high-energy photon and electron beams in experimental and clinical use, especially for radiation therapy. We examined the expanded dosimetric characteristics of GDs including dose linearity up to 500 Gy, uniformity among GD lots and for individual GDs, the angular dependence, and energy dependence of 4 therapeutic x-ray qualities. In addition, we measured the dosimetric features (dose linearity, uniformity, angular dependence, and energy dependence) of the GD for electron beams of 10 different electron energy qualities. All measurements with the exception of dose linearity for photon beam were performed in a water phantom. For high-energy photon beams, dose linearity has a linear relationship for a dose ranging from 1 to 500 Gy with the coefficient of determination; R² of 0.998. The uniformity of each GD of dose measurements was within ±0.5% for four GD lots and within ±1.2% for 80 GDs. In terms of the effects of photon beam angle, lower absorbed doses of within 1.0% were observed between 60° and 105° than at 90°. The GD energy dependence of 4 photon beam energy qualities was within ±2.0%. On the other hand, the result of the dose linearity for high-energy electron beams showed well fitted regression line with the coefficient of determination; R² of 0.999 between 6 and 20 MeV. The uniformity of GDs exposed to the nominal electron energies 6, 9, 12, 16, and 20 MeV was ±1.2%. In terms of the angular dependence to electron beams, absorbed doses were within 2.0% between 60° and 105° than at 90°. In evaluation of the energy dependence of the GD at nominal electron energies between 5 and 20 MeV, we obtained responses between 1.1% and 3.5% lower than that for a cobalt-60 beam. Our results show that GDs can be used as a detector for determining doses when a high-energy photon beam is used, and that it also has considerable potential for dose measurement of high-energy electron beam.